A Bit of theory


Data centers Triton

The effective way to centralise servers and other active elements requires a change in the methods of cooling and protecting this equipment. The solution is – a data center.

What is a data centre?

Modern data centers differ significantly from the early versions of this method of installing servers and other equipment. The original data centers have been established on the backbone of Internet connections from the 1990s. Large data halls were built primarily as a space perfectly protected in terms of security, uninterrupted power supply and with adequate capacity of mostly optical communication lines. The individual cabinets were then leased to users for their technical and Internet applications. These centres almost always had raised floors with high loading, beneath which were located all cabling and cooling systems. The cooling was mostly centralised so the entire room was air conditioned regardless of the distribution of the thermal load and without the possibility to effectively regulate the cooling for individual cabinets or the data hall.
With the development of telecommunications, new protocols and an increase in the transmission line capacity, high-speed connections have become available without the need to place the device directly onto the backbone connections. In parallel, a revolution took place on another front - processing power and storage capacity. Processor performance grew dramatically, multi-core processors began to appear along with new operating systems. Hard drives and other storage media multiplied in their capacity.
Server operating systems began to use available resources for sharing multiple, simultaneously running applications and from there it was only a small step to share one physical computer for running multiple operating systems simultaneously - for visualisation. As a result, most companies now run their applications either on their own servers dedicated to specific applications or use the services of the increasingly popular virtualisation and the so-called cloud-hosting. Both methods require a high density of installed computing power. Because these applications are often critical to the operation of businesses and institutions, it requires a fail-safe power supply, physical protection, and controlled cooling. All these aspects are covered by the concept of a data centre. Over time, a standard was established for the design and construction of data centres. Cabinets are placed in groups, usually in the form of two rows spaced 1,200 mm apart (two standard raised floor tiles). The aisle between the cabinets is then roofed and closed at the ends by sliding doors. In large data centres, dividing doors can also be found within these units, which split them down into smaller sections.
The main product of our company's data centre solution is the RDA cabinet with a load capacity of 1,800 kg in a version adapted for the construction of data centres. Other necessary components such as ceiling panels of various types, including sliding doors, as alternative self-closing etc., make a complete modular system. We also offer a complete range of raised floors for installations that allow their use.
The floor loading capacity is particularly critical in the rooms of future data centre. In cases where it is not possible to use the raised floor (low room height, insufficient permissible floor loading, etc.) we can offer an alternative, in the form of In-Row cooling units with top media inlet and condensate pump. This advanced solution offers an extra-large installed cooling capacity on a small footprint. By connecting multiple cabinets in a data center, the need for cooling optimization begins to arise, among other things. Uncontrolled air flows are costly and inefficient.
By using RDA cabinets and components designed for data centres, it is possible to assemble a complete data center easily and efficiently. The most common solution in terms of cooling:

Reference data center TRITÓNData center with centralized air conditioningScheme of data center cooling


Data center cooling principles

Hot / cold aisle Hot / cold aisle
Arranging cabinets into hot / cold aisles is a standard solution for data centres. Cabinets are oriented face-to-face, while cold air is supplied through perforated tiles in a raised double floor. Standard ANSI/TIA/EIA-942-A recommends a cold aisle width of 1.2 metres. This is generally the size of two double floor tiles. Cold air is supplied through perforated tiles at the front of the cabinets, which is delivered to each of them by fans. Cold air is supplied to the active elements through a door with 80% perforation. In this case, the double floor is used to deliver cold air and it is necessary that all other openings in the floor, such as the cable entries, are covered. The reason is to maintain static air pressure in the double floor and minimise cold air loss.
Contained cold aisle Contained cold aisle
The solution of open hot / cold aisles presents possible shortages in the recirculation of heated air and, therefore, the risk of creating so called hot-spots - locally overheated areas. The solution is a contained cold aisle. This is a closed modular expandable system which physically separates the cold air from the exhalation of hot air. It creates a separate area for hot and cold air and prevents them from mixing. Cool air is fed into the closed aisle through perforated tiles of the raised floors or locally using the side cooling units, which are mounted directly in line between the cabinet. The standard width of the contained cold aisle is 1.2 metres (two floor tiles) or 1.8 m (three floor tiles). At the ends, the aisle is also equipped with a glass sliding door. The use of this solution is becoming standardised and is recommended mainly for its cooling capacity and efficiency in achieving the lowest energy consumption of the data centre.
Closed modular solution Closed modular solution
The closed modular solution enables maximum energy efficiency and scalability for long-term development of a data center. This solution can be designed and manufactured tailored to customer's needs. In one room, there can be zones not only with different operating temperatures, but also with different density of the thermal load. The solution is characterised by a high-IP cabinet. This also provides protection for the installed components from dust and moisture.
The side cooling units are attached directly with the cabinets to create a closed module with an internal cold zone at the front part of the cabinet and hot zone at the rear of the cabinet. This solution allows you to combine any number of cabinets and cooling units in the module. Our specialists will prepare a project proposal for you to ensure the necessary space capacity required for installation of the equipment and the corresponding power conditioning, including any required redundancy.
Floor feed Floor feed
This method increases the efficiency of the cold air through the delivery from double floor to the installed equipment.
The cabinet is installed on the opening in the double floor. A deflector, located at the bottom of the cabinet, directs cool air to its front section. In this case, cold air is further directed in the front section of the cabinet by the door without perforations, these may be of glass or metal. The hot air is extracted from the rack either by doors with 80% perforation or the cabinet ceiling.
By installing a cool air supply regulator to the bottom of the cabinet, the amount of air may be adjusted, or delivery can be completely discontinued when the cabinet is not in use. The advantage of this cooling method is great flexibility in planning of the room usage. Installing cabinets in hot and cold aisle is not required if the hot and cold air is separated inside the cabinet. To achieve this, it is necessary to install a separating frame inside the cabinets for a strict separation of cold and hot air.
Floor feed with plenum return Floor feed with plenum return
A possible disadvantage of cold aisle and cooling supply from the floor and return to the room is that the hot air is brought into the surroundings of the installed equipment. This does not cause a complication when it is already considered in the data centre design stage. In certain cases, a possible solution is to completely separate the warm air in areas with high thermal loads due to the concentration of the installed equipment.
The solution is to supply cooling air from the room or raised floors and return it to the ceiling. This is the solution when the hot air does not return into the hall but is fed to the ceiling or double ceiling. A rear deflector located in the upper part of the cabinet helps to optimise the flow of hot air into the outlet extension. A large adapter allows the passage of large quantities of air at a relatively low speed.
A cold air intake is on the front door of the cabinet, and hot air is discharged through the outlet extensions to the ceiling / double ceiling above the devices. Air conditioning units take the hot air from the ceiling, cool it, and deliver it back under the raised floor. The air-cooling circuit is closed. This solution provides high efficiency cooling for large volumes of hot air. Research indicates that this solution can be used to cool up to 30 kW per cabinet.

Our specialists will gladly help you choose the optimum solution for your needs.
By choosing the right type of cabinet and accessories, you can save significant amount of money spent on the operation of your equipment.


Data center design

This critical stage of the data center construction has an indefinite solution. It depends on the cabinet arrangement, the distribution of the heat load and its size, the choice of thermal scheme (hot / cold aisle, zonal distribution of cold etc.) and many other aspects.
When selecting the most suitable arrangement it is necessary to take into account the type of cooling system (under-floor cooling, In-Row cooling units ...) and with regard to the cooling medium used, also select the outer part of the system.
Choice of the cooling medium must be done with respect to outdoor climatic conditions, the distance of the data center from the external units and the elevation between them. Depending on conditions, a water cooling with the appropriate addition of antifreeze or system operating with liquid refrigerant gas can be selected.
With regard to safety and redundancy required for service operations, it is necessary to design the complete system properly, both on the inside of the data center and on the side of radiators or condensers.
Furthermore, the requirements of humidity control must be taken into account. Humidity lower than 30% carries a risk of damage to the installed equipment by static electricity surge; high humidity can lead to condensation.
We offer cooling systems from leading manufacturers operating in this highly specialized field of data centres and telecommunication equipment cooling for many years. Thanks to the close cooperation and support of their development teams, we can offer you proven and guaranteed solutions.
Designing a functional, reliable, financially and operationally efficient cooling systems for the data centre is not an easy task and our specialists, who will recommend the optimum solution in terms of investment and operating costs, are fully available to you.

Power distribution units

Equipment installed in data centers often has significant power consumption. Along with the need for a power supply, this also brings the issue of measuring consumption and the need to remotely control the device. Therefore, in our range you will find power distribution panels, which not only allow you to switch individual devices on or off, but also provide information on the temperature and humidity in the cabinet, check the correct functioning of the condensate drain of the cooling unit, signal an alarm when the cabinet door is opened and other conditions defined by you. Any changes can then be reported using the integrated software through a computer network and thus allow you to oversee the data center without the physical presence of the operator.
Distribution panels with management systems exist in many different models. Whether in terms of dimensions, where we offer solutions from the standard 19” panels to large vertical panels designed for house distribution systems, or in terms of different inputs (16A-64A, single-phase / three-phase). It is possible to choose from many product lines according to the required panel functionality (measurement of the panel as a whole unit or measurement of individual outlets, the control panel as a whole or individual outlet switching, additional monitoring functions temperature / humidity / door contact / water flood sensor).

We will be happy to advise you on choosing the most suitable solution.